Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Abatement Technologies HVAC Cleaning in Atlanta: What to Know First
We provide independent Abatement Technologies HVAC cleaning across Atlanta, and most standard whole-system cleanings run $350 – $600 for a typical home, with coil treatment and deeper component work pushing toward $800 in larger systems. Turnaround is usually one visit: we arrive, clean, treat, and verify within a single two-to-four-hour window. If you own a home in Atlanta with dirty coils, a clogged blower, or an air handler that’s been ignored for a few years, this page tells you exactly what we do and what it costs.
Call (470) 408-4927 for a free estimate. No guessing games, no phone tag.
How Abatement Technologies Products Fail – and How We Fix Them
Abatement Technologies builds commercial-grade HVAC and indoor-air equipment, mostly for hospitals, schools, and data centers. But a good number of their units end up in Atlanta homes, especially high-end new builds and teardown remodels in places like Buckhead, Ansley Park, and Virginia-Highland. Their systems are overbuilt for residential use. That’s good news for durability and bad news if they ever do fail, because the parts and the people who understand them are not on every corner.
- Louvered containment units pulling Atlanta pollen straight through the intake. The Abatement Technologies H2000 series and larger H3000 series are negative-air machines first. In Atlanta, March through May turns every intake into a pollen magnet. What we see: the pre-filter loads up until the motor is starving for air, pressure differentials go sideways on the gauges, and the unit either squeals or runs hot. Our fix: deep-clean the intake plenum, replace the pre-filters with the correct MERV-8 or MERV-11 stack, and verify the HEPA seal isn’t bypassing. Then we clean the condenser coil on the cooling side so it isn’t compounding the problem.
- Evaporator coils on Abatement Technologies AHU-05 and AHU-10 air handlers are buried deep. These aren’t slide-in residential coils. They’re multi-row commercial coils with tight fin spacing, which means they hold onto Atlanta’s humidity-driven bio-growth longer than a standard residential coil. By the time the homeowner notices weak airflow or a musty smell, the coil is often 40 – 60% blocked. We open the handler, pressure-wash the coil with a non-acidic foaming cleaner rated for mixed-metal coils, then apply a coil treatment that slows re-fouling. Skipping the treatment on these units means you’ll be back in eighteen months.
- Blower wheels on the Abatement Technologies CBR and PBR series get a “dust glaze” that throws the wheel off balance. These blowers are built for constant duty, so when the wheel loads up unevenly, the bearings take the beating rather than the motor. Early symptom: a low thrum at startup that fades as the unit warms. We remove the wheel, pressure-clean every blade, and remount with a torque check. That procedure alone saves the motor on a lot of Atlanta units that would otherwise be dead by year seven.
- Heat exchanger sooting on Abatement Technologies HE-75 series units. This one is specific enough that if you own an HE-75 and you’re seeing gray streaks around the supply registers, you already know something isn’t right. The root cause is almost always incomplete combustion from a burner that’s never been serviced, and the symptom is fine gray particulate that lands on furniture near the vents. We clean the exchange surfaces, check the burners and gas pressure, and document the before-and-after with photos so there’s no question the work was done. This is also the job where we’re most likely to tell you to have a combustion safety check before we leave.
- Abatement Technologies condensate pans on AHU-05/10 units crack at the drain bung. It’s a materials thing, not a workmanship thing. The pan itself is rigid polymer, the bung fitting is press-fit, and after a few Atlanta summers of heat cycling it fractures and starts weeping. We reseal with a two-part epoxy rated for wet environments, replace the bung fitting if it’s beyond saving, and reroute the drain line with a proper P-trap. Every one of these we’ve opened in Atlanta had at least a teaspoon of standing water in the pan from a slow leak the homeowner never noticed until the ceiling below it started staining.
Styles & brands we work with
Our Abatement Technologies HVAC Cleaning Process
Here’s what a call to (470) 408-4927 gets you, start to finish.
- 1
Call and book. A live person answers. We schedule a window, and you get a live trackable arrival time through the Relay Standard before we ever show up.
- 2
Walkthrough and written price. I walk the system with you and point out what I’m seeing. Before anything is unbolted, you get a written price. That number does not change at the door.
- 3
Contain and prep. We lay down drop cloths and run Abatement Technologies containment where the job calls for it. Atlanta homes with old plaster or finished basements get the full treatment.
- 4
Clean the full air path. We clean the evaporator coil, blower wheel, condenser coil, air handler interior, and the heat exchanger surfaces. We use Nikro HEPA extraction so the loosened material goes into the vacuum, not back into your living room.
- 5
Treat and reassemble. We apply a coil treatment that slows regrowth in Atlanta’s humidity, reassemble, and run the system through a full cycle to verify pressures, temps, and airflow.
- 6
Show you the proof. Before-and-after photos, a written summary of what we found and what we did, and that 365-Day Done Right Promise in writing: if the work isn’t right within a year, we return and correct it at no charge.
See the difference
Before
After
Before
After
Before
AfterWhat Abatement Technologies HVAC Cleaning Costs in Atlanta
Most standard whole-system cleanings on Abatement Technologies residential equipment in Atlanta run $350 – $600. That covers the coil, blower, housing interior, and a basic coil treatment on a single-system home. Larger homes with two systems, or commercial-grade air handlers like the AHU-10, land in the $600 – $900 range because there’s simply more surface area and more disassembly time.
What moves the price: accessibility of the air handler, whether the condenser needs a deep coil pull, and whether we’re adding an extended coil treatment or HEPA filter upgrade. We quote the whole job as one flat price per system before we touch a vent. No per-vent pricing, no “oh by the way” add-ons. Call (470) 408-4927 for an exact number. Estimates are free.
Why Atlanta Homeowners Call Cardinal Air Duct Atlanta for Abatement Technologies Work
Because we show up with the right tools and we tell you the truth before we spend your money. We run Rotobrush rotary brush systems, Nikro HEPA vacuums, and Abatement Technologies containment units on every job that warrants them. Our techs are background-checked and uniformed, and you know the name of the person walking through your door before they arrive. If you’ve got an Abatement Technologies unit and you’re worried about voiding a warranty with the wrong cleaning method, we know what’s safe and what isn’t. And if you own a different brand too, we work on Lennox, Trane, and Carrier systems every week across Atlanta, so one call covers the whole house.
Every job includes a written price before work starts, a written guarantee on the repair work, and the 365-Day Done Right Promise. That’s not a promotion. It’s how we operate.
FAQs
Yes. We regularly clean Abatement Technologies H2000 and H3000 series negative-air units and commercial-grade air handlers installed in large Atlanta homes, carriage houses, and home office suites. The process is the same as residential work, but we quote it as its own flat price because the equipment takes longer. Call (470) 408-4927 and we’ll give you a straight number.
No, not with our process. We follow manufacturer-safe cleaning methods: no acidic coil cleaners on mixed-metal coils, no abrasive wheel cleaning that could throw balance, and no aftermarket parts unless you specifically approve them. We use OEM-spec filters and are careful around the components Abatement Technologies warranties. As an independent Abatement Technologies service provider, we’re not authorized by the manufacturer, but we keep your warranty intact by doing the work the way it was designed to be done.
Usually within a few days, depending on the time of year. Spring and early fall are our busiest seasons because Atlanta pollen and humidity spike. If you call (470) 408-4927 now, you’ll have a live person on the line and a trackable arrival window before the call ends.
We show you before-and-after photos of the coil, blower, and housing interior before we leave. No photos, no invoice – that’s the Relay Standard. If you want to stand at the unit and look inside yourself, we’ll walk you through it. There’s nothing to hide.
Depends on the unit’s age and condition, but most of the time cleaning is the better first move. We’ll tell you straight if a unit is too far gone to justify the cost. We don’t sell replacement equipment, so when we say clean it, that’s the truth, not an upsell.
Tell me what you need, I’ll tell you what it costs – we’ll both sleep better tonight. Call (470) 408-4927 for a free estimate on Abatement Technologies HVAC cleaning in Atlanta.
Written by Omar Haddad, Owner & Lead Technician, Cardinal Air Duct Atlanta at Cardinal Air Duct Atlanta, serving Atlanta and nearby areas.